Nouvelle puce pour la wii - News

Nouvelle puce pour la wii

   
Posté par le 02/08/07 à 21:32:12
2165 affichages, 1 commentaire
 
Du nom de "wii boss", une nouvelle puce de type 'quick solder' pour la wii est censé sortir le 3 aout 3007.
imageimage

La puce sera équipée d'un programmateur externe pour la mettre à jour (flasher) a l'aide d'un port RS-232 (port série)

Fonctions de la puce:
Quote :

Wii-BOSS! The world first fully upgradeable internal modchip for the Nintendo Wii.
“Almost all other conventional and homebrew modchips consist of two parts where the code is held, of which only the smaller EEPROM section of the chip can be changed easily. This EEPROM part of the code is very useful for small pre defined simple on or off selectable 1’s and 0’s and possibly a very small “additional feature” section. For example: Speed setting your chip or enabling multi-zone. However, if you want to update the entire chip, you need to physically remove the chip from the Wii, put it on a programmer, reprogram it, and then reinstall the chip into the Wii. This is not something you want to be doing constantly keep up with new optimized modchip codes for the Nintendo Wii.”

• The Wii-Boss is designed as a ‘quick solder’ chip with an external ribbon cable that can be left inside the machine, taped down on the back of the Wii, or even hidden inside the memory card bay. This chip can be fully programmed inside the machine with any code that supports the 12f629 PIC Microchip.

• The Wii-Boss is also designed to allow external booting off the ribbon cable, therefore protecting the user against ever having to pull the Wii apart ever again if their requirements for a particular style of modchip change. External adapters to make competitor modchips and PC applications like DVD-Tool boot externally have already been designed and will be produced soon after the initial release of the premier product for a very minimal charge. These will likely be included in future kits at no extra charge.

• The Wii-boss even comes packaged with its own RS-232 port external programmer. Software for the programmer is open source and therefore also provided free. The programmer is based on an open source project and therefore could be ‘modded’, theoretically, to be used as a standard RS-232 PIC programmer.

• R.R.P. for the entire packed is USD$25 including the Wii-SP JDM programmer. The cost will obviously much cheaper in bulk quantities. Wholesale quantities start from just 2 kits.

At the time of writing the wii-boss supported the following codes (in no particular order):

Wii-Free - last stable release ver2.45
YOASM - last stable release ver1.7
Winja – last stable release ver2.0 (deluxe currently not available)
Open-Wii - last stable release ver1.3
Wii-skas - last stable release unknown
MaxBoot - last stable release ver1.0 (redirection code for external booting)

Supported software for the programmer:
IC Prog ver 1.05e


Site officiel



Pages: 1
Messages:
^ Déconnecté quent08
#1, posté le 23/09/08 à 19:54:13
Membre
523 messages
Connaisseur
star
avatar
3007 ... ::surprised:: On serait deja au ciel ::wtf:: tu ne veut plutot pas dire 2007
Choisir un Film : La meilleure solution quand on ne sait pas quel film regarder

Pages: 1

Ajouter commentaire:
Créez un compte ou identifiez vous pour poster un commentaire.
 

rss


Pour votre téléphone, Jailbreak iPhone et Jailbreak iPad. - Hack PS3 - Hacker sa WiiU - Hacker PS Vita - Rage Comics, troll face - Retrouvez chaque jour des image drole sur internet grâce à LOLTube. - Meme Internet
257 connectés (0 membre, 257 anonymes)© 2007-2015 Attila